Openwrt
Small linux for routers
Router
http://wiki.openwrt.org/inbox/tp-link.tl-wr1043nd
Write firmware
mtd write /tmp/openwrt-brcm47xx-squashfs.trx linux reboot
mtd -e firmware write /tmp/openwrt-ar71xx-tl-wr1043ndv1-squashfs-universal.bin firmware reboot
Which version of openwrt is installed.
cat /etc/banner
read /var/log/messages
logread
packages
update package list
opkg update
install openvpn
opkg install http://downloads.openwrt.org/kamikaze/8.09.2/brcm-2.4/packages/zlib_1.2.3-5_mipsel.ipk opkg install http://downloads.openwrt.org/kamikaze/8.09.2/brcm-2.4/packages/libopenssl_0.9.8i-3.2_mipsel.ipk opkg install http://downloads.openwrt.org/kamikaze/8.09.2/brcm-2.4/packages/liblzo_2.03-1_mipsel.ipk opkg install http://downloads.openwrt.org/kamikaze/8.09.2/brcm-2.4/packages/openvpn_2.0.9-5.1_mipsel.ipk
mount jffs2
mount -t jffs2 /dev/mtdblock3 /jffs/
list wireless
iw phy
serial cable
http://www.nslu2-linux.org/wiki/HowTo/AddASerialPort http://wiki.openwrt.org/oldwiki/openwrtdocs/customizing/hardware/serial_console http://wiki.openwrt.org/inbox/tp-link.tl-wr1043nd#oem.installation.using.the.tftp.and.rs232.method http://jethomson.wordpress.com/2010/02/21/diy-usb-to-serial-cable-for-3usd/
openwrt
http://eko.one.pl/openwrt/ http://openwrt.groov.pl
recover tp-link wr1043nd
Strip firmware
you can use any hexeditor to delete the first 0x20200 byte, it will start with 01 00 00 00 54 50 after delete
dd if=wr1043nv1_en_3_9_17_up_boot\(091118\).bin of=tplink.bin.257 skip=257 bs=512
tftp server
code.bin containing openwrt firmware.
Create a serial cable from a nokia ca-42 datacable.
- Cut cable of ca-42 and locate the four cables. gnd, rx, tx, ttl
Serial port cummunication values.
115200 8n1
open tp-wr1043nd
- Remove the two screws from under the rubber feet at the back of the device.
- Unscrew all three retaining nuts on the SMA connectors and carefully push them into the housing.
- Push one of the bottom screws back into place to separate the top from the outer frame.
- With the top slightly open, push the bottom plastic away from the outer frame.
- Remove outer frame.
- With a flathead screwdriver or similar tool, gently pry the two front clips apart.
- Carefully separate the bottom guide posts from the top of the unit, then pull the top section forward.
Image Connect cables to wr1043nd and plug usb in computer. Start terminal emulator.
screen /dev/ttyUSB0
Start router and look at terminal. When waiting for 1 second press
tpl
- when it show autobooting, it will let you get into U-boot.
- you can set the router ip address by
setenv ipaddr 192.168.1.1
- tftpd server address by
setenv serverip 192.168.1.100
What to write in ubootin
erase 0xbf020000 +7c0000 7c0000: size of the firmware (be aware that u can have diffrent size so u will brick your router) tftpboot 0x81000000 code.bin cp.b 0x81000000 0xbf020000 0x7c0000 bootm 0xbf020000